This procedure describes how to configure PLM client LPAR's in multiple domains with the PLM server and HMC sitting in different domains than the client LPAR. This has typically caused RMC authentication problems in the past and this procedure circumvents it.

---

• Login as "root" to the client LPAR and create a .rhosts file that contains entries for the PLM server using all know short names, long names and associated IP addresses. For example, client LPARS in the "mcc2" network may require a ".rhosts" file that appears as follows:

  ddcapnim01					root
  ddcapnim01-mc2					root
  ddcapnim01-mcc2					root
  ddcapnim01.man.capgeminienergy.net		root
  ddcapnim01-mc2.man.capgeminienergy.net		root
  ddcapnim01-mcc2.man.capgeminienergy.net		root
  206.245.36.100					root
  
  

---

• Now configure the "inetd" daemon to provide "rsh" access and refresh the "inetd" daemon

  vi /etc/inetd.conf
  refresh -s inetd
  
  

---

• Test rsh communication from the PLM server to the client LPAR:

  rsh lparname-mc2.man.capgeminienergy.net ls
  
  

---

• If this is successful, then test the RMC communications from the PLM server and client LPAR:

  CT_CONTACT=lparname-mc2.man.capgeminienergy.net lsrsrc IBM.HostPublic
  
  

---

• If this is successful, then test the RMC communications from the client LPAR to the PLM server. If unsuccessful, see the section regarding rsct configuration resets.

  CT_CONTACT=ddcapnim01-mcc2.man.capgeminienergy.net lsrsrc IBM.HostPublic
  
  

---

• If this is successful, then perform the PLM setup. If unsuccessful, see the section regarding rsct configuration resets.

---

• To perform a PLM setup from the PLM server run the following command:

  /etc/plm/setup/plmsetup lparname-mc2.man.capgeminienergy.net root ddcapnim01-mcc2.man.capgeminienergy.net
  
  

---

• Test the RMC PLM communications from the PLM Server to the client LPAR.

  CT_CONTACT=lparname-mc2.man.capgeminienergy.net lsrsrc IBM.LPAR
  
  

---

• If unsuccessful, edit the "/var/ct/cfg/ctrmc.acls" file on the client LPAR and edit the "IBM.LPAR" stanza to containt the following info:

  IBM.LPAR:
  	*		*		rw
  	UNAUTHENT	*		rw
  
  

Troubleshooting: RSCT configuration reset

---

• To reset the RSCT configuration on a client LPAR, run the following commands:

  cd /usr/sbin/rsct/install/bin
  ./uncfgct
  ./cfgct
  ./recfgct
  cd /usr/sbin/rsct/bin
  ./rmcctrl -z
  ./rmcctrl -A
  ./rmcctrl -p
  
  

---

• Then rerun the "plmsetup" command before continuing and retest the IBM.HostPublic communications in both directions.

---

• It may be necessary to remove the PLM server identities from the trusted host list on the client LPAR:

  cd /usr/sbin/rsct/bin
  ./ctsthl -d -n ddcapnim01
  ./ctsthl -d -n ddcapnim01-mc2
  ./ctsthl -d -n ddcapnim01-mcc2
  ./ctsthl -d -n ddcapnim01.man.capgeminienergy.net
  ./ctsthl -d -n ddcapnim01-mc2.man.capgeminienergy.net
  ./ctsthl -d -n ddcapnim01-mcc2.man.capgeminienergy.net
  
  

---

• Then rerun the "plmsetup" command before continuing and retest the IBM.HostPublic communications in both directions.